M.
Butkus, NJ.
On-line camera manual library
If you find this manual useful, how about a donation of $3 to: M.
Butkus, 29 Lake Ave., High Bridge, NJ 08829-1701
and send your e-mail address
so I can thank you. Most other places would charge you $7.50 for a electronic copy
or
$18.00 for a hard to read Xerox copy.
TABLE OF CONTENTS
|
Nomenclature 1 Specifications 3 SIMPLIFIED GUIDE FOR BASIC OPERATION 4 1. Battery Installation 6 2. Automatic Film Speed Setting 7 3. Automatic Film Loading 7 4. Film Cartridge Window 8 5. Holding the Camera 9 6. Viewfinder Indications 9 7. Autofocus Shooting 10 |
8. Focus Lock System , 11 9. Power Zooming 12 10. Flash Photography . I 13 11. Effective Flash Range 14 12. Self-timer Photography 14 13. Automatic Film Rewinding , 15 14. Manual Power Film Rewinding , 15 15. Optional Accessories (AUTO DATE) 16. Attaching the Neckstrap . 20 : 20 17. Care of the Camera |
NOMENCLATURE
 |
1. Manual rewind button 2. Self-timer button 3. Main switch 4. Shutter release button 5. Self-timer indication LED 6. Lens |
|
7. Exposure metering window 8. Viewfinder 9. Flash 10. Auto focus window 11. Film type window 1 2. Back cover |
13. Take up spoolwww.4.butkus.org 14. Film tip mark 1 5. Battery compartment cover 1 6. Viewfinder eyepiece 1 7. Power zoom button (Tale/Wide) 18. Film guide |
 |
19. Film chamber 20. Automatic film speed setting contacts 21. Film rewind shaft 22. Tripod socket 23. Frame counter 24. OK monitor (Green) LED
|
SPECIFICATIONS
MAIN FEATURES: -35 mm compact zoom camera
-Auto DX sensing programmed AE
-Fully motorized film transport
-Built-in sensor -Built-in electronic self-timer
-Long life lithium battery
FILM TYPE: 135 size film
PICTURE SIZE: 24x36 mm
LENS: Aperture ratio: F/3.7-6.9
Focal length: f/35 mm-70 mm
Zooming: Power zoom
FINDER: Type: Actual image zoom finder
Magnification: 0.41-0.78x
Coverage: 82%
Diopter: -1.0 Diopter
Finder indications: Auto focus frame, parallax compensation mark, LED Indication: OK monitor (Green
LED)
FOCUSING SYSTEM: Type: Infrared auto focusing system:
AF effective range: 1.0 (35.4")--inf.
Prefocus and cancelable: Yes
SHUTTER: Type: Stepping motor controlled changeless shutter
Type of shutter release: Electromagnetic release
Shutter speed range: Approx. 1/50 sec.-1/500 sec.
EXPOSURE METER: Type: Programmed AE
Exposure range: W: EV 9.5-17.0, T: EV 11.3-18.8
Film speed sensing: Automatic for ISO 100, 200,
400 and 1000. ISO 100 setting for non DX films.
TRANSPORTATION: Film loading: Auto loading First frame setting: Automatic setting by closing film door
Film winding: Motorized winding
Film rewinding: Motorized rewinding
Rewinding actuation: Automatic
Rewinding stop: Automatic
Mid-roll rewind button: Yes
Frame counter: Built-in
FLASH: Type: Sensor flash
Flashmatic: Yes
Auto recharging: Yes
Effective range: W: 1.0-5 m (35.4"-16.4'),
T: 1.0-2.7 m (35.4"-8.9')
Recycle time: Approx. 3 seconds OTHER FEATURES: Power source: Lithium battery pack (2CR5x1): replaceable 4www.butkus.org
Battery checker: Yes
Film door window: Built-in
Tripod screw: Built-in: U-1/4"
Self-timer: Built-in: approx. 10 sec. /
Auto power shut off: Yes /
Strap: Attachable
Size: 137(L)x77(H)x61(W) mm (53x3.0x2.4") /
AUTO DATE: 137(L)x77(H)x64(H) mm /5-3X3.0X2.5")
Weight: 350 grams. (12.3 ounces) /3
AUTO DATE: 360 grams. (12.6 ounces) /
1.
Install lithium battery. 2. Slide the main switch to the "POWER" position.
3. Load the film correctly and close the back door 4. Be sure the frame counter shows "1" in the frame counter window.
5. Direct the AF mark toward your subject. 6. Release the shutter by pressing the shutter release button gently.www.4.butkus.org
7. Automatic film rewinding starts at the end of the roll. The frame counter will show "S" upon completion. 8. Remove the exposed film.
(1 ) Use a coin and turn it toward the arrow mark to unlock the battery cover. Open the battery cover by sliding it away from
the camera (Fig. 1).
(2) Place a 6 volt lithium battery (2CR5) in the battery compartment in accordance with the positive (+) and the negative (-)
marks shown inside (Fig. 2).
(3) Slide the battery cover back to its closed position and lock the battery cover (Fig. 3).
Note:
* When the shutter release is locked or when winding/ rewinding becomes extremely slow, replace the battery with a new one.
* Battery performance declines in cold temperatures. Keep the camera as warm as possible in cold weather.
* The lithium battery will last about three years when used at a frequency of one roll of film of 24 exposures with 50% use of
flash on a monthly basis, at room temperature. (Chinon Laboratory Testing)
2. Automatic film speed setting 3. Automatic film loading (2) Insert the film cartridge into the film chamber (Fig. 6).
(3) Place the trimmed end of the film on the take-up spool up to the film tip mark. Make sure that the film lies flat between the
film guides and that the film perforations engage the sprocket teeth (Fig. 7).
(4) Close the back cover. The film will automatically advance to the first frame and the frame counter will show "1 " in the
frame counter window (Fig. 8).www.4.butkus.org
Note:
* If the frame counter does not show "1 " after the film is loaded, open the back cover and reload the film.
* When placing the trimmed end of the film on the take-up spool, the length of the film pulled out from the film cartridge should
not be too long or too short relative to the film tip mark. If too much film is pulled out from the cartridge, adjust the film
length by pushing the film back into its cartridge so that the trimmed end of the film will be precisely placed at the film tip
mark.
4. Film cartridge window
* Hold your camera firmly in both hands with at least one elbow at your side to ensure camera steadiness when taking a
picture.
6. View finder
1. AF mark
2. Parallax marks
3. AF indicator LED (Green)
Note:www.4.butkus.org
* When taking a picture closer than 1.2 meters (3.9 ft) the image area is indicated by the two parallax marks in the top left and
right of the viewfinder. Compose the
(1 ) Direct the center of the AF mark toward the subject (Fig. 10).
(2) Gently press the shutter release button halfway. The AF indication LED (Green) in the viewfinder frame will light up (Fig.
11).
(3) Fully press the shutter release button to take the photograph
Note:
* If the AF indication LED blinks continuously, the subject is too close to the camera to be focused properly.
This feature may be used when the main subject is located "OFF CENTER" in the viewfinder.
(1 ) Focus on the main subject by placing the subject within the auto-focus mark and partially depress the shutter release
button until the AF indication LED lights up (Fig. 12).
(2) While holding the shutter release button in this position, recompose the subject within the viewfinder and fully depress the
shutter release to take the picture (Fig. 13).
(3) The locked focus setting will be held only as long as you partially depress the shutter release button and the AF indication
LED remains lighted. This focus lock feature can be cancelled by removing your finger from the release button.
This camera is equipped with a power zoom to enable you to select the zoom range to compose the picture.
(1 ) Turn the power zoom lever to the right (TELE) or to the left (WIDE) to change the zoom range (Fig. 14).
(2) Select the ideal composition by turning the power zoom lever while looking at the subject through the viewfinder.
(3) Press the shutter release button completely to take the photograph. Note:
* When the camera is not in use, the main switch should be turned to the "OFF" position in order to protect the lens system
from accidental damage.
* Never push or twist the lens barrel as this may cause damage to the zoom lens.
* The zoom system will not function while
This camera automatically senses the scene brightness and fires the flash when needed.
(1 ) When the shutter release button is pressed halfway and the AF indication LED blinks once and then disappears, it means
the flash is being charged. You must wait until it glows steadily before you take a picture. If it does not blink during the
flash charging cycle or does not glow at all, the battery is too weak and battery replacement is required.
(2) The flash will be fully charged in about three seconds when using a fresh battery. Note:
11. Effective flash range
Wide TELE The self-timer feature allows the photographer to be in the picture.
(1 ) Place the camera on a tripod or other firm support, and direct the multi AF mark toward the subject (Fig. 15).
(2) Press and hold the self-timer button on the top of the camera and then press the shutter release button completely to start
the self-timer operation (Fig. 16).www.4.butkus.org
(3) The self-timer indication LED will light up and the picture will be taken in approximately 10 seconds. The self-timer
indication LED will initially glow and then will blink for two seconds before the shutter is released. Note:
13. Automatic film rewind
(1 ) When the roll of film is completed, a delay of from two to three seconds will
occur before the camera automatically starts rewinding the film. During the rewinding, the frame counter will count backwards.
(2) When the rewinding is completed, the motor will stop automatically and the frame counter will reset to the
start "S" position (Fig. 17).
(3) Push the back cover release button down to open the back cover and remove
the cartridge from the film chamber. Be sure the frame counter shows "S" before opening the back cover. 14. Manual rewind
If you want to rewind the film before it has been fully exposed, push the rewind
button on the top of the camera. Use a ball-point pen or a similar object which is
not too sharp. The camera will then perform as it did under the "FILM REWINDING" section (Fig. 18).
(A) Year/month/day setting
Example: 24 December, 1990
1. With a ball point pen or similar object (fingernail), press the MODE button for the year/month/day setting.
2. With a ball point pen or similar object (fingernail), press the SELECT button to locate the "year" position. A blinking number
will appear.
3. With a ball point pen or similar object (fingernail), press the SET button to set "90".
4. Press the SELECT button to locate the "month" position above whose number the "M" (month) indication always appears
and whose number appears blinking. Then, press the SET button until "12" appears.
5. Press the SELECT button to locate the "day" position. The blinking "day" indicating number will appear. Then, press the
SET button until "24" appears. Note:
B) Hour/minute setting
Example: 19:58 (7:58 PM)
1. With a ball point pen or similar object (fingernail), press the MODE button for day/hour/minute setting.
2. With a ball point pen or similar object (fingernail), press the SELECT button until a blinking "!" appears. Press the SET
button to start "00" second.
3. Press the SELECT button to locate the blinking "minute" position. Press the SET button to set "58".
4. Press the SELECT button to locate the blinking "hour" position. Press the SET button to set "19". (2) DATA IMPRINTING
When the above procedure (1) is completed, select, by depression of the MODE button, the year/month/day,
month/day/year, day/month/year mode, day/hour/ Note:
* The data will not be sharply defined if the picture content on the bottom right hand corner of a horizontal
picture is white or yellow.
* Imprint display "-" in the upper right corner of the LCD will blink until the completion of the imprinting.
IMPORTANT
LCD Information
17. Care of the Camera
This camera is a precision photographic instrument. When used with care it will provide years of
trouble-free service. Protect your camera from dirt, rain, dampness and excessive heat. Avoid touching the lens. To clean the
lens, wipe it gently with a soft lintless cloth or tissue. Do not use eyeglass tissues as they might damage the lens coating. Do
not open and touch the inside of the camera as possible high voltage in the flash circuitry can be dangerous. When the
camera will not be in use for a
Photo cell: CdS
Simplified guide for basic operation
1. Battery installation
The film speed is automatically set when using a
DX coded film of ISO 100 to ISO 1000
(Fig. 4). Non DX film will be set to ISO 100. When using reversal film (Slide Film), use films of ISO 100, 200, 400, or 1000.
Always load and unload your camera in subdued light and never in direct sunlight. This will greatly
minimize the possibility of fogging the film. (1 ) Open the back cover by sliding the back cover release button downwards (Fig.
5).
This camera is equipped with a convenient film cartridge window so that you can confirm what type of film is being
used (Fig. 9).
5. Holding the camera
* Do not cover the lens, flash unit, exposure metering window or auto focus windows with your fingers.
* Always press the shutter release button gently to pre- vent blurred pictures caused by camera shake.
7. Auto focus shooting
8. Focus lock system
9. power zooming
10. Flash photography
* The shutter cannot be released until the flash is completely charged.
* The flash will be charged even if the shutter release is kept fully depressed. The shutter will be released immediately upon
the completion of the flash charging cycle.
ISO 100 3.3 to 16.4 ft
ISO 200 3.3 to 23.3 ft
ISO 400 3.3 to 33.1 ft
ISO 1000 3.3 to 46.9 ftISO 100 3.3 to 8.9 ft
ISO 200 3.3 to 12.5 ft
ISO 400 3.3 to 17.4 ft
ISO 1000 3.3 to 24.9 ft
12. Self-timer
* To cancel the self-timer during its "count down", press the self-timer button once or slide the main switch to the "OFF"
position.
15. Optional Accessories (AUTO DATE)
(1) YEAR/MONTH/DAY, DAY/HOUR/MINUTES SETTINGS
* Every time you press SET button, the number shown on the display window proceeds consecutively. When you press and
hold the SET button for more than a second, the numbers will change continuously.
Make sure that the "-" appears lit on the LCD before releasing the shutter during imprinting.
· The Auto Date back is powered by the camera's battery. The following steps should be taken as soon as possible
to avoid any loss of date.
1. When replacing the battery, do so as quickly as possible. If the Auto Date back is left without a battery for two to three
hours, the time and date readings may be incorrect even after a replacement battery has been installed.
2. If an incorrect LCD indication appears after the installation of a new battery, reinstall the battery in the battery compartment
or "reset" it by releasing the shutter.
3. Always check for the correct time and date indications after replacing the battery.
1. To clean the unit, use a dry cloth without any cleaning agent
2. Do not depress the buttons with sharp or pointed object such as a knife.
3. Rough handling may result in damage to the unit.
4. Keep the lithium battery out of the reach of children.
1. Use the unit at temperatures between -1 0°C and +50°C (14°F-122°F) for normal operation
of the liquid crystal.
2. Do not expose the unit to the direct rays of the sun for a long time since the LCD may turn black at temperatures above
60°C (1 40°F).
3. Performance of the LCD declines as the temperature becomes low.
16. Attaching the neck strap.
The strap goes alongside the body.